#Networx alarm cabinet standoffs serial number#
#Networx alarm cabinet standoffs install#
#Networx alarm cabinet standoffs manual#
#Networx alarm cabinet standoffs full#

Requires horizontal and vertical lock and latch case support (provided by door manufacturer).

Notch on both sides of 2 1/8' hole to accommodate Drill 3/8' thru-bolt holes first, then drill 2 1/8' hole. Mark hole centers on door and door edge.ģ. Fold and place template on high edge of door at the recommended height from floor. Square and clamp to door before drilling See Fig. For best results, align the Installation Jig to door with a The typical small and large system configurations.Ģ.

#Networx alarm cabinet standoffs manual#

This manual includes the hardware installation instructions for the This means that locksĬan be installed on the doors and immediately be put into use via In addition to wireless communication, these wireless door locksĬan also be programmed at the keypad.

#Networx alarm cabinet standoffs serial number#

PDL6100/26D - Cylindrical Trilogy® Networx™ Wireless AccessĬontrol Lock with built in HID Proximity ID Card Reader, fullmetal digital keypad, integral bi-directional radio, 4 C-cell battery-operated (batteries supplied), serial number ID card, standard format SCI keyway for manual key override, 4⅞' ASAĭL6100/26D - Cylindrical Trilogy Networx PIN-Code WirelessĪccess Control Lock, as above, with full-metal digital keypadĬonvenient way to keep track of and ensure all locks are enrolled Keeping complete and accurate records saves time because after the wireless network is set up,Īny programming added via the keypad must be re-added to DLWindows and downloaded back to the lock(s). Recommend you keep hardcopy records (in a secure location) ofĪll Users, their User Codes, and any proximity cards that may Start programming your wireless lock via the keypad, we Keypad cannot be retrieved into DL-Windows. Therefore, all lock programming added via the Zones, and Schedules is available as a temporary convenience toĪllow the lock to be put into use before installing and configuring a Note: Keypad programming of User Codes, Features, Time Up and running, you can run DL-Windows to link the 'virtual' system saved on your computer with the 'real' lock hardware on the But in the end,Īfter your lock hardware is physically installed and the network is

#Networx alarm cabinet standoffs install#

Up the network and install the lock hardware later. If you wish, you can even start by designing a 'virtual' system within DL-Windows (creating new Accounts, adding Users and configuring lock features, etc.), then set Therefore, you can install the locks on the doors before configuring the wireless network, or you can set up the wireless networkįirst and add locks later. Keypad programming-even before a wireless network is set up. That you fill out a new yellow-colored 'Lock ID Card' with the Mounted, the Gateways search for new locks, allowing them to beįor every new wireless lock installed on a door, we recommend To ensure each physical lock is identified correctly by DLWindows, the factory assigns each lock a unique serial number Īfter locks are installed in the doors and the Gateways are

#Networx alarm cabinet standoffs full#

In this way, the software allows full programming and control of each lock in the system. Intermediate device called a Gateway that communicates to a With a few clicks of the computer mouse, you can use your computer to retrieve logs, download User Codes and program features into and out of each PDL6100 and DL6100 series wirelessĭL-Windows software is installed on a computer that is connected to a computer network connected to this network is an 'wireless' communication, the various cables and/or AL-DTMĭata Transfer Module devices are NOT required to transfer data.

The Trilogy Networx™ PDL6100 and DL6100 series door locksĪllow you to upload and download programming features wirelessly using a computer connected to a computer network. Names and services described in this manual are for identification purposes only and may be trademarks of their respective companies. Windows is a registered trademark of the Microsoft Corporation. Note: ProxCard® and ProxKey® are trademarks of the HID© Corporation. (Note: Technical Service is for security professionals only)